Electrical Safety Level 2 Practice Test

These questions are part of the practice quiz. Start practicing

• A 600-volt, current-limiting fuse with a 200-kA interrupting rating when arcing currents are in the current limiting region can impact which components of risk?
• Which statement best describes the requirement for electrical PPE selection?
• What does a clearance accomplish in relation to LOTO and arc-flash protections?
• Unqualified persons shall be trained in, and be familiar with, any electrical safety-related practices necessary for their safety. This training requires documentation including each employee's name and training dates, retained for the duration of employment per which clause?
• Differentiate between the restricted approach boundary and the limited approach boundary.
• The bus configuration associated with the highest incident energy is which of the following?
• What does the term incident energy refer to in arc flash safety?
• What is the role of training in maintaining Level 2 electrical safety compliance?
• Which practice is important for safety during OCPD maintenance?
• What is the purpose of a hazard assessment for temporary wiring installations?
• In the context of OCPD selection, which characteristic, if present, is essential for minimizing arc-flash hazards?
• What information must a typical energized work permit contain?
• The threshold in cal/cm for an incurable burn is ?
• What is the impact of fast fault-clearing times on arc-flash risk?
• Which statement best describes the difference between grounding and bonding in electrical systems?
• Under lockout/tagout program requirements, the employer shall be responsible for which of the following?
• Explain the difference between a fuse and a circuit breaker in electrical protection.
• Which device, after it clears an overload, is not able to be reset?
• In arc flash terminology, what unit is incident energy measured in?
• Article 90 covers the use, application, and arrangement of NFPA 70E. Which term completes the trio?
• Incident energy would be the highest for which of the following bus configurations?
• Why is it essential to maintain electrical test equipment calibration and verification before use?
• Why is dry, clean PPE essential when working around high-energy equipment?
• PPE Category 2 typically implies protective equipment appropriate for a certain arc energy level. Which description best matches Category 2?
• Who shall use test equipment to test circuit elements and verify deenergization?
• When should arc-rated clothing be removed or replaced during a task?
• Why is it important to update arc flash hazard analysis after system changes?
• The hazard assessment certification must identify the workplace evaluated, the person certifying the evaluation, the date(s) of the hazard assessment, and what else?
• In arc flash hazard analysis, who is typically responsible for identifying hazards and implementing control measures?
• If an incident energy label is prepared using the incident energy analysis method, PPE levels are determined by which source?
• What is a temporary protective grounding device, and when is it used?
• Which overcurrent protective devices will always have an instantaneous trip component as part of their Time-Current Characteristic?
• Which of the following is a cause of an electrical shock hazard?
• Which step is performed last when re-energizing equipment after maintenance?
• If maintenance is not performed, which PPE determination method is applicable?
• Placing a circuit breaker equipped with an energy reduction maintenance switch next to the equipment it supplies power to will impact which component of risk?
• Low voltage 48 VDC current under fault conditions could pose which hazard?
• Define incident energy in arc flash terminology and explain how it affects PPE selection.
• Per NFPA 70E Article 105, what is one of the employer's responsibilities?
• What is the purpose of updating labeling after system changes in arc-flash hazard analysis?
• According to Subpart K, when equipment or circuits are deenergized, they must be rendered inoperative and have tags attached at all points where such equipment or circuits can be energized.
• What is the proper method to reset a circuit breaker that has tripped and is in the center position?
• Electrical conductors and circuit parts shall not be considered in an electrically safe work condition until all applicable requirements of the electrical safety standard are met. Which option best describes those requirements?
• The available fault current is influenced by which factors?
• What does MCCB stand for?
• Which device is typically used as the main protective device in switchgear to interrupt large fault currents?
• Why is it essential to perform a test for absence of voltage after locking out and tagging out?
• Which factor is not listed as a risk component affected by protective devices in the material?
• How does the role of equipment maintenance records support electrical safety?
• Which of the following is a key consideration in system design to reduce electrical hazards?
• What should be checked immediately before re-energizing equipment after maintenance?
• If available fault current increases, what effect does this have on the PPE category required for arc flash protection?
• In hazard assessment certification, which item is identified as the workplace evaluated?
• Which of the following are steps in establishing and verifying an electrically safe work condition?
• How does incident energy relate to PPE category, and how are categories ordered from lowest to highest?
• What is the correct order of the Hierarchy of Risk Control Methods as described in NFPA 70E?
• A worker is performing maintenance on a 208-volt panelboard supplied by a current-limiting fuse with an available fault current of 54 kA. Using the PPE Category method, what level of PPE is required?
• Which of the following best describes the primary purpose of electrical maintenance in ensuring safety?
• What is the primary purpose of establishing an electrically safe work condition (ESWC) and who is responsible for authorizing it?
• Adding line-side barriers to the service overcurrent protective device impacts which component of risk?
• What are the key steps to re-energize equipment after maintenance?
• Which statement about general lockout/tagout requirements is true?
• Under NFPA 70E, who must ensure that contract employees follow the work practices required by the standard and the safety-related rules required by the host employer?
• What is the primary purpose of the job safety plan and job briefing conducted before electrical work?
• What is the purpose of barricades and warning signs around an electrical hazard work area?
• What is a hazard risk assessment in the context of electrical work?
• Per Subpart K, deenergized equipment must be rendered inoperative and what else?
• Which statement lists the main components of arc-rated PPE with examples?
• Under lockout/tagout planning requirements, a simple procedure is permitted when which condition exists?
• Explain the purpose of arc flash labels and how to interpret incident energy and PPE requirements from them.
• As you move farther from the arcing source, what happens to the incident energy?
• Which portion of the molded case circuit breaker's trip curve yields the lowest incident energy when arcing current is within that region?
• In the hierarchy of risk control methods, which is the last resort?
• What is touch potential and how does proper grounding affect it?
• Which PPE item is primarily used to protect the eyes and face from arc flash hazards?
• What is the purpose of insulating mats or covers in electrical work?
• Which design practice can significantly reduce the likelihood of accidental contact with live electrical components?
• After performing a disconnection, which step is essential before re-energizing?
• What step is essential to confirm a circuit is de-energized before work begins?
• How should you respond to an electrical fire, and which extinguisher is typically recommended?
• Incident energy is defined as the amount of energy of what type impressed on a surface during an electrical arc event?
• Which of the following maintenance practices is most important to keep flexible cords safe?
• What is the primary purpose of designing overcurrent protective devices with respect to incident energy?
• What does arc-rated clothing refer to?
• What is a primary goal of integrating protective devices into system design?
• Which statement best describes when electrical equipment should be inspected and what inspectors look for?
• What is the purpose of arc flash labeling on equipment?
• Electrical safety training documentation must include which of the following?
• Why is maintaining zero energy state verification important before maintenance?
• What document provides incident energy and PPE requirements for arc flash hazards?
• When using a digital multimeter near live circuits, which precautions ensure safety?
• The standard referenced in the contractor responsibilities is which of the following?
• Which statement correctly describes the relationship between incident energy analysis and PPE selection?
• Which aspect underscores the importance of regular maintenance for electrical equipment?
• Work on a 480-volt panelboard supplied by a molded-case circuit breaker with available fault current of 18 kiloamps. Based on the PPE Category method, what PPE category is required?
• Regular maintenance helps ensure protective devices operate as intended, reducing incident energy. Which option best describes this effect?
• How does the condition of maintenance affect incident energy levels in electrical systems?
• What is the lowest PPE Category that can be worn for a 480-volt panelboard with 23 kiloamps of fault current at the panelboard and supplied from a 200-amp current-limiting fuse operating in the current limiting region?
• How can proper grounding and bonding techniques contribute to reducing electrical hazards?
• Which statement best describes hazard assessment documentation for PPE?
• Which statement best describes a qualified person under NFPA 70E and what criteria establish qualification?
• Which statement about NFPA 70E safety program is true?
• Which fault current type results from a loose or poor connection causing current to flow along an unintended path, often producing an arc?
• Which scenario would likely result in a higher available fault current?
• Why is it important to reassign tasks to qualified personnel?
• When maintenance is not performed on the electrical distribution system, which method is used to determine proper PPE?
• Under the lockout/tagout program, which statement reflects the employer's responsibilities?
• If regular maintenance is not performed, incident energy in electrical systems is likely to:
• Which statement best describes the purpose of barricades and warning signs around an electrical hazard work area?
• How can hazards be controlled when working near overhead power lines?
• After maintenance on electrical tools, what should you do before resuming work?
• For a molded case circuit breaker with an electronic trip unit, which portion of the trip curve provides the fastest clearing time?
• An 'Unqualified Person' is defined as a person that is ? a qualified person.
• When the protecting circuit breaker is not maintained, NFPA 70E requires which of the following?
• How do you select the correct PPE level for a given task?
• Incident energy relates to OCPD design and maintenance and refers to
• How do you determine the incident energy value for a given piece of equipment?
• What is meant by the term "flash protection boundary" and how are boundaries determined?
• Which task is described as reducing the severity of injuries by using an energy reduction switch?
• What is essential before maintenance or testing on OCPDs to ensure no energy remains?
• Which practice best supports electrical safety by ensuring up-to-date information and compliance?
• Under NFPA 70E, when is it permissible to perform work on energized equipment, and what permit is typically required?
• The arcing current is what relative to the bolted fault current value?
• There are no requirements from Article 110 that apply in addition to 120.6 when applying 120.6. True or False?
• Describe the steps to perform a safe switching operation on a service disconnect.
• Exposure to electrical hazards from work on, near, or with conductors or equipment in electric-utilization installations is covered by which subpart?
• How are PPE requirements determined from labels in arc flash safety?
• How should electrical tools be maintained to prevent electrical hazards?
• The fault current study is the beginning point for which analyses?
• Which device reduces arcing energy and helps to reduce incident energy?
• Lockout/tagout planning requires which of the following to be considered?
• The lockout/tagout program and procedures required by 120.2 through 120.6 shall be audited by a qualified person at intervals not to exceed one year.
• What is the purpose of Lockout/Tagout (LOTO) in electrical safety, and what are the key steps?
• Which statement best defines a qualified person in the context of arc flash hazard analysis?
• Which statement is most accurate about NFPA 70E Chapter 2 requirements for maintenance of flexible cords and cables?
• Who audits the lockout/tagout program? (At intervals not to exceed one year)
• Which statement aligns with NFPA 70E requirements for PPE maintenance?
• When working downstream of a power circuit breaker installed in a panelboard, what is the lowest PPE category method possible?
• Define touch voltage and step voltage and describe how to mitigate each.
• Which of the following is not a potential risk associated with poor electrical maintenance?
• Which PPE category can be used when the incident energy calculation method determines the incident energy is 8.3 cal/cm2 ?
• What factors determine the selection of a protective ground during testing?
• Name a sign that equipment needs maintenance before use.
• When the incident energy label is created based upon the incident energy analysis method, the level of PPE to be worn can be determined by which of the following?
• Elevated incident energy in electrical systems most directly increases the risk of which injury?
• Which part of a protective device's trip curve responds to very high fault currents within milliseconds?
• What is the primary benefit of incorporating maintenance-friendly designs into electrical systems?
• Subpart C requires employers to instruct employees in recognizing and avoiding unsafe conditions and the regulations applicable to what?
• Tingling sensation can be expected on a 60-hertz AC circuit when the current passing through the body in milli-amperes is ?
• What is the typical outcome of a hazard assessment for temporary wiring installations?
• What information is typically required to perform a detailed calculation of the 3-phase available fault current?
• Which hazard is primarily caused by insulation failure or damaged wiring?
• What is the primary focus of NFPA 70E?
• In arc-flash hazard analysis, what factors determine PPE requirements?
• Which item is not a direct focus of fault current studies?
• Work is being performed on a 208-volt panelboard supplied by a molded-case circuit breaker that has not been maintained in over 10 years. The available fault current at the panelboard is 10 kiloamps. What level of PPE is to be worn based on the PPE Category method?
• During inspections, what is a typical labeling requirement for equipment?
• The electrical safety program per NFPA 70E requires which of the following?
• Which of the following is not considered the protecting overcurrent protective device for a panelboard directly fed from the secondary conductors of a transformer?
• What is the lowest PPE category that can be worn for a 480-volt panelboard with 23 kiloamps of fault current at the panelboard and supplied from a circuit breaker that has not been maintained in the last seven years?
• Which statement is most accurate about NFPA 70E Chapter 2 requirements for maintenance of personal protective equipment (PPE)?
• How should non-electrical personnel be protected when work near energized equipment is required?
• What is the primary difference between shock hazard and arc flash hazard?
• Which statement about grounding is true?
• Which statement best describes the purpose of protective devices in system design?
• What role do spotters play during certain energized tasks?
• Which overcurrent protective device is most commonly found in switchgear?
• Replacing a transformer with the same kVA and voltage ratings but a lower %Z has which impact on available fault current downstream?
• What is the impact of neglecting maintenance on electrical safety?
• Which statement best describes the role of incident energy calculations in arc flash safety?
• What is a dead-front panel and why is it important for safety?
• What is the primary purpose of NFPA 70E's risk control hierarchy?
• Why is reporting near-misses and hazards important in electrical safety?
• Who is responsible for completing the job safety plan and conducting the job briefing before starting a job involving exposure to electrical hazards?
• The General Duty Clause requires employers to furnish a workplace free from what hazards?
• What type of test must insulating gloves receive in addition to the daily inspection?
• Which maintenance-related design feature most directly supports easier servicing?
• A circuit breaker that is equipped with an energy reduction maintenance switch can impact which component of risk?
• Which NFPA 70E section defines the Hierarchy of Risk Control Methods?
• What is a verified absence of voltage test and why is it important to perform it more than once?
• Dropping a tool on energized parts and not making a solid connection causing current to flow outside of the path is an example of which type of fault current?
• Under Subpart C, employers must instruct employees in recognizing and avoiding unsafe conditions and the regulations applicable to what?
• What are typical examples of arc-rated PPE fabrics and garments?
• Arc rating is defined, in part, as the value attributed to materials, expressed in what units?
• What is a critical step to take before initiating maintenance or testing procedures on OCPDs?
• When selecting a protective ground during testing, which factors are essential?
• Which safe-work practice is recommended when performing de-energized electrical work?
• The burn threshold in energy terms is expressed in which unit?
• What does LOTO stand for in safe de-energizing procedures?
• When selecting OCPDs for installation, what factor is crucial in mitigating arc-flash hazards?
• Which practice enhances electrical safety when replacing or inspecting OCPDs?
• How do you verify that a circuit is de-energized before work begins?
• Which standards govern the use of insulated tools?
• What is the primary reason for using insulated tools when working on electrical equipment?
• The employer shall document that each employee has received the lockout/tagout procedure training required by 110.4(B). Which subsection specifies this training?